Rear Work Lamps


Rounding out the illumination modifications on the Nomad is a pair of three-inch, 12W LED work lamps mounted on the rear Surco roof rack stanchions.


Although the interior cargo lamp has been converted to LED, I needed more light on the food prep area along with a bit more illumination rearward, though the LED reverse light upgrade puts out great coverage. 


The work lamps are wired from the control panel I built into the platform. 


I pulled a hot lead with a ground from the Blue Sea Blade fuse block to the rear of the platform and wired the circuit through the voltmeter, to the 12V marine socket, to the USB, to the switch and terminated at the lamps.


Twelve watts is just right, not overpowering, spotting the work area and the storage drawer and when we're not cooking we can bounce them off the awning for a soft indirect light.


Comments

  1. rasheedasableMarch 4, 2022 at 12:07 PM

    Casino games – The most popular games, ranked
    What are the most popular casino games in the casino category and which 전라북도 출장샵 ones do you 청주 출장안마 like to play? — Discover the 보령 출장마사지 best slots, table 서울특별 출장샵 games, 광주 출장샵 video poker and live dealer

    ReplyDelete

Post a Comment

Popular posts from this blog

Platform and Drawer System

Image
If you've been reading along on this build you know that there was a dog deck and a folding utility shelf installed, neither of which worked as well as I would have liked. Add to that one of the reasons I went with this 2.5 is its room to create a sleeping platform, and I decided to do a do-over, making this Interior Modification, Part 2, combining a platform with a drawer system.  I studied a number of DYI systems on Expo and other build threads, making decisions on materials and dimensions, but keeping all this driven by our overland history of what has worked and what we wish we had. The driving need here for us was to have the ability to pull over, level out, roll out pads and bags and go to sleep.  We've done the RTT route and have a Kodiak ground tent, both with pros and cons. Being able to sleep in the Monty seems to be the best compromise for us; easy set-up and access, great weather protection and climate control, off the ground away
Read more

Transfer Case Shifter Replacement

Image
When I first tested this Monty it shifted into 4 and 4l without any issues, even the rear locker kicked in just fine. After purchase I took it out to wheel more aggressively to baseline its suspension and it wouldn't shift into low range and that's when after a bit of research I learned of this drivetrain's Achilles' heel. In the image of my shifter above, surrounding the lever that engages the transfer case forks is a brown plastic articulating ball or at least what's left of it. While this particular plastic outlived Mitsubishi's warranty, it went to pieces later in many a Montero/Pajero/Shogun. The fix is not a new aftermarket part - none exists that I could find - but to score a junkyard find of a previous iteration found in earlier vehicles that have a white plastic ball instead of brown. I swapped mine the other day after sourcing a white-balled shifter from a local Montero enthusiast who picks them up from local pick-a-part yards. The job is pretty
Read more

Reverse Light Upgrade

Image
The back-up lamps on the 2.5 are more of a suggestion of light than actual practical illumination, so I decided to do quick and inexpensive upgrade. I've had good luck with CREE style LEDs previously, as long as I replaced all the hardware with stainless. I came across these NiLight 18W flush mount flood lights and thought I'd roll the dice and give them a try. Eighteen bucks, why not? The install required trimming a bit of the opening for the stock lamps since the NiLight height is about a quarter inch taller. Remove the housing. Then remove the lamp from the housing. I clipped the the socket off from the wires. Before fitting clean the area around the opening to remove the footprint from the previous housing.  I used a jig saw with a metal cutting blade to score the bottom edge of the opening, creating "teeth" that will be pulled to match the height requirement of the new housing. Using a pair of ViseGrips, grab a tooth and slowly mo
Read more